Add warning not to edit boards.txt (#383)

* Remove redundant/wrong second board.mcu in boards.txt

Fixes #380

Boards.txt had the setting board.mcu twice.  The first one was correct,
while the second one wasn't and shouldn't have been there.  Remove it.

* Include fix from @rei-vilo in #381

README.md

@@ -19,8 +19,11 @@ See https://arduino-pico.readthedocs.io/en/latest/ along with the examples for m
 * Adafruit Trinkey RP2040 QT
 * Arduino Nano RP2040 Connect (preliminary)
 * Cytron Maker Pi RP2040
+* Cytron Maker Nano RP2040
 * Invector Labs Challenger RP2040 WiFi
+* Invector Labs Challenger NB RP2040 WiFi
 * Invector Labs Challenger RP2040 LTE
+* Invector Labs RPICO32
 * Melopero Shake RP2040
 * SparkFun ProMicro RP2040
 * uPesy RP2040 DevKit

cores/rp2040/Arduino.h

@@ -30,6 +30,7 @@
 #include <pins_arduino.h>
 #include "hardware/gpio.h" // Required for the port*Register macros
 #include "debug_internal.h"
+#include <RP2040.h> // CMSIS
 
 // Try and make the best of the old Arduino abs() macro.  When in C++, use
 // the sane std::abs() call, but for C code use their macro since stdlib abs()
@@ -95,7 +96,7 @@ void analogWriteResolution(int res);
 #endif
 
 #include "SerialUART.h"
-#include "RP2040.h"
+#include "RP2040Support.h"
 #include "Bootsel.h"
 
 // Template which will evaluate at *compile time* to a single 32b number

cores/rp2040/RP2040USB.cpp

@@ -52,7 +52,6 @@ mutex_t __usb_mutex;
 #endif
 
 #define USBD_DESC_LEN (TUD_CONFIG_DESC_LEN + TUD_CDC_DESC_LEN)
-#define USBD_MAX_POWER_MA (250)
 
 #define USBD_ITF_CDC (0) // needs 2 interfaces
 #define USBD_ITF_MAX (2)

cores/rp2040/SerialUART.cpp

@@ -96,7 +96,9 @@ void SerialUART::begin(unsigned long baud, uint16_t config) {
     gpio_set_function(_tx, GPIO_FUNC_UART);
     gpio_set_function(_rx, GPIO_FUNC_UART);
     _running = true;
-    _peek = -1;
+    while (!_swFIFO.empty()) {
+        (void)_swFIFO.pop(); // Just throw out anything in our old FIFO
+    }
 }
 
 void SerialUART::end() {
@@ -107,20 +109,30 @@ void SerialUART::end() {
     _running = false;
 }
 
+// Transfers any data in the HW FIFO into our SW one, up to 32 bytes
+void SerialUART::_pumpFIFO() {
+    while ((_swFIFO.size() < 32) && (uart_is_readable(_uart))) {
+        _swFIFO.push(uart_getc(_uart));
+    }
+}
+
 int SerialUART::peek() {
     CoreMutex m(&_mutex);
     if (!_running || !m) {
         return -1;
     }
-    if (_peek >= 0) {
-        return _peek;
+    _pumpFIFO();
+    // If there's something in the FIFO now, just peek at it
+    if (_swFIFO.size()) {
+        return _swFIFO.front();
     }
+    // The SW FIFO is empty, read the HW one until the timeout
     if (uart_is_readable_within_us(_uart, _timeout * 1000)) {
-        _peek = uart_getc(_uart);
-    } else {
-        _peek = -1; // Timeout
+        // We got one char, put it in the FIFO (which will now have exactly 1 byte) and return it
+        _swFIFO.push(uart_getc(_uart));
+        return _swFIFO.front();
     }
-    return _peek;
+    return -1; // Nothing available before timeout
 }
 
 int SerialUART::read() {
@@ -128,16 +140,18 @@ int SerialUART::read() {
     if (!_running || !m) {
         return -1;
     }
-    if (_peek >= 0) {
-        int ret = _peek;
-        _peek = -1;
+    _pumpFIFO();
+    if (_swFIFO.size()) {
+        auto ret = _swFIFO.front();
+        _swFIFO.pop();
         return ret;
     }
+    // The SW FIFO is empty, read the HW one until the timeout
     if (uart_is_readable_within_us(_uart, _timeout * 1000)) {
+        // We got one char, return it (FIFO will still be empty
         return uart_getc(_uart);
-    } else {
-        return -1; // Timeout
     }
+    return -1; // Timeout
 }
 
 int SerialUART::available() {
@@ -145,7 +159,8 @@ int SerialUART::available() {
     if (!_running || !m) {
         return 0;
     }
-    return (uart_is_readable(_uart)) ? 1 : 0;
+    _pumpFIFO();
+    return _swFIFO.size();
 }
 
 int SerialUART::availableForWrite() {
@@ -153,6 +168,7 @@ int SerialUART::availableForWrite() {
     if (!_running || !m) {
         return 0;
     }
+    _pumpFIFO();
     return (uart_is_writable(_uart)) ? 1 : 0;
 }
 
@@ -161,6 +177,7 @@ void SerialUART::flush() {
     if (!_running || !m) {
         return;
     }
+    _pumpFIFO();
     uart_tx_wait_blocking(_uart);
 }
 
@@ -169,6 +186,7 @@ size_t SerialUART::write(uint8_t c) {
     if (!_running || !m) {
         return 0;
     }
+    _pumpFIFO();
     uart_putc_raw(_uart, c);
     return 1;
 }
@@ -178,6 +196,7 @@ size_t SerialUART::write(const uint8_t *p, size_t len) {
     if (!_running || !m) {
         return 0;
     }
+    _pumpFIFO();
     size_t cnt = len;
     while (cnt) {
         uart_putc_raw(_uart, *p);

cores/rp2040/SerialUART.h

@@ -23,6 +23,7 @@
 #include <Arduino.h>
 #include "api/HardwareSerial.h"
 #include <stdarg.h>
+#include <queue>
 #include "CoreMutex.h"
 
 extern "C" typedef struct uart_inst uart_inst_t;
@@ -61,8 +62,10 @@ private:
     uart_inst_t *_uart;
     pin_size_t _tx, _rx;
     int _baud;
-    int _peek;
     mutex_t _mutex;
+
+    void _pumpFIFO();
+    std::queue<uint8_t> _swFIFO;
 };
 
 extern SerialUART Serial1; // HW UART 0

lib/pico_base/pico/version.h

@@ -12,8 +12,8 @@
 #define _PICO_VERSION_H
 
 #define PICO_SDK_VERSION_MAJOR    1
-#define PICO_SDK_VERSION_MINOR    2
+#define PICO_SDK_VERSION_MINOR    3
 #define PICO_SDK_VERSION_REVISION 0
-#define PICO_SDK_VERSION_STRING   "1.2.0"
+#define PICO_SDK_VERSION_STRING   "1.3.0"
 
 #endif

lib/platform_inc.txt

@@ -15,6 +15,9 @@
 -iwithprefixbefore/pico-sdk/src/common/pico_util/include
 -iwithprefixbefore/pico-sdk/src/rp2040/hardware_regs/include
 -iwithprefixbefore/pico-sdk/src/rp2040/hardware_structs/include
+-iwithprefixbefore/pico-sdk/src/rp2_common/cmsis/include
+-iwithprefixbefore/pico-sdk/src/rp2_common/cmsis/stub/CMSIS/Core/Include
+-iwithprefixbefore/pico-sdk/src/rp2_common/cmsis/stub/CMSIS/Device/RaspberryPi/RP2040/Include
 -iwithprefixbefore/pico-sdk/src/rp2_common/hardware_adc/include
 -iwithprefixbefore/pico-sdk/src/rp2_common/hardware_base/include
 -iwithprefixbefore/pico-sdk/src/rp2_common/hardware_claim/include

package.json

@@ -1,6 +1,6 @@
 {
   "name": "framework-arduinopico",
-  "version": "1.10905.0",
+  "version": "1.10909.0",
   "description": "Arduino Wiring-based Framework (RPi Pico RP2040)",
   "keywords": [
     "framework",

package/package_pico_index.template.json

@@ -41,6 +41,9 @@
                   {
                      "name": "Arduino Nano RP2040 Connect"
                   },
+                  {
+                     "name": "Cytron Maker Nano RP2040"
+                  },
                   {
                      "name": "Cytron Maker Pi RP2040"
                   },

platform.txt

@@ -29,6 +29,8 @@ runtime.tools.pqt-elf2uf2.path={runtime.platform.path}/system/elf2uf2
 
 compiler.path={runtime.tools.pqt-gcc.path}/bin/
 
+compiler.libraries.ldflags=
+
 # Compile variables
 # -----------------
 
@@ -96,13 +98,13 @@ discovery.rp2040.pattern="{runtime.tools.pqt-python3.path}/python3" -I "{runtime
 # ----------------
 
 ## Compile c files
-recipe.c.o.pattern="{compiler.path}{compiler.c.cmd}" {compiler.c.flags} {build.usbpid} -DF_CPU={build.f_cpu} -DARDUINO={runtime.ide.version} -DARDUINO_{build.board} -DBOARD_NAME="{build.board}" -DARDUINO_ARCH_{build.arch} {compiler.c.extra_flags} {build.extra_flags} {build.debug_port} {build.debug_level} {build.flags.optimize} {includes} "{source_file}" -o "{object_file}"
+recipe.c.o.pattern="{compiler.path}{compiler.c.cmd}" {compiler.c.flags} {build.usbpid} {build.usbpwr} -DF_CPU={build.f_cpu} -DARDUINO={runtime.ide.version} -DARDUINO_{build.board} -DBOARD_NAME="{build.board}" -DARDUINO_ARCH_{build.arch} {compiler.c.extra_flags} {build.extra_flags} {build.debug_port} {build.debug_level} {build.flags.optimize} {includes} "{source_file}" -o "{object_file}"
 
 ## Compile c++ files
-recipe.cpp.o.pattern="{compiler.path}{compiler.cpp.cmd}" {compiler.cpp.flags} {build.usbpid} -DF_CPU={build.f_cpu} -DARDUINO={runtime.ide.version} -DARDUINO_{build.board} -DBOARD_NAME="{build.board}" -DARDUINO_ARCH_{build.arch} {compiler.cpp.extra_flags} {build.extra_flags} {build.debug_port} {build.debug_level} {build.flags.optimize} {includes} "{source_file}" -o "{object_file}"
+recipe.cpp.o.pattern="{compiler.path}{compiler.cpp.cmd}" {compiler.cpp.flags} {build.usbpid} {build.usbpwr} -DF_CPU={build.f_cpu} -DARDUINO={runtime.ide.version} -DARDUINO_{build.board} -DBOARD_NAME="{build.board}" -DARDUINO_ARCH_{build.arch} {compiler.cpp.extra_flags} {build.extra_flags} {build.debug_port} {build.debug_level} {build.flags.optimize} {includes} "{source_file}" -o "{object_file}"
 
 ## Compile S files
-recipe.S.o.pattern="{compiler.path}{compiler.S.cmd}" {compiler.S.flags} {build.usbpid} -DF_CPU={build.f_cpu} -DARDUINO={runtime.ide.version} -DARDUINO_{build.board} -DBOARD_NAME="{build.board}" -DARDUINO_ARCH_{build.arch} {compiler.S.extra_flags} {build.extra_flags} {build.debug_port} {build.debug_level} {includes} "{source_file}" -o "{object_file}"
+recipe.S.o.pattern="{compiler.path}{compiler.S.cmd}" {compiler.S.flags} {build.usbpid} {build.usbpwr} -DF_CPU={build.f_cpu} -DARDUINO={runtime.ide.version} -DARDUINO_{build.board} -DBOARD_NAME="{build.board}" -DARDUINO_ARCH_{build.arch} {compiler.S.extra_flags} {build.extra_flags} {build.debug_port} {build.debug_level} {includes} "{source_file}" -o "{object_file}"
 
 ## Create archives
 # archive_file_path is needed for backwards compatibility with IDE 1.6.5 or older, IDE 1.6.6 or newer overrides this value
@@ -116,7 +118,7 @@ recipe.hooks.linking.prelink.1.pattern="{runtime.tools.pqt-python3.path}/python3
 recipe.hooks.linking.prelink.2.pattern="{compiler.path}{compiler.S.cmd}" {compiler.c.elf.flags} {compiler.c.elf.extra_flags} -c "{runtime.platform.path}/boot2/{build.boot2}.S" "-I{runtime.platform.path}/pico-sdk/src/rp2040/hardware_regs/include/" "-I{runtime.platform.path}/pico-sdk/src/common/pico_binary_info/include" -o "{build.path}/boot2.o"
 
 ## Combine gc-sections, archives, and objects
-recipe.c.combine.pattern="{compiler.path}{compiler.c.elf.cmd}" "-L{build.path}" {compiler.c.elf.flags} {compiler.c.elf.extra_flags} {compiler.ldflags} "-Wl,--script={build.path}/memmap_default.ld" "-Wl,-Map,{build.path}/{build.project_name}.map" -o "{build.path}/{build.project_name}.elf" -Wl,--start-group {object_files} "{build.path}/{archive_file}" "{build.path}/boot2.o" {compiler.libpico} -lm -lc {compiler.libstdcpp} -lc -Wl,--end-group
+recipe.c.combine.pattern="{compiler.path}{compiler.c.elf.cmd}" "-L{build.path}" {compiler.c.elf.flags} {compiler.c.elf.extra_flags} {compiler.ldflags} "-Wl,--script={build.path}/memmap_default.ld" "-Wl,-Map,{build.path}/{build.project_name}.map" -o "{build.path}/{build.project_name}.elf" -Wl,--start-group {object_files} "{build.path}/{archive_file}" "{build.path}/boot2.o" {compiler.libraries.ldflags} {compiler.libpico} -lm -lc {compiler.libstdcpp} -lc -Wl,--end-group
 
 ## Create output (UF2 file)
 recipe.objcopy.uf2.pattern="{runtime.tools.pqt-elf2uf2.path}/elf2uf2" "{build.path}/{build.project_name}.elf" "{build.path}/{build.project_name}.uf2"

tools/libpico/CMakeLists.txt

@@ -53,6 +53,7 @@ target_link_libraries(pico
 	hardware_vreg
 	hardware_watchdog
 	hardware_xosc
+	cmsis
 	pico_bit_ops
 	pico_bootrom
 	pico_bootsel_via_double_reset

tools/libpico/make-libpico.sh

@@ -23,6 +23,7 @@ for type in boot2_generic_03h boot2_is25lp080 boot2_w25q080 boot2_w25x10cl; do
         arm-none-eabi-gcc -march=armv6-m -mcpu=cortex-m0plus -mthumb -O3 \
                          -DNDEBUG -DPICO_FLASH_SPI_CLKDIV=$div \
                          -c "$PICO_SDK_PATH/src/rp2_common/boot_stage2/$type.S" \
+                         -I "$PICO_SDK_PATH/src/boards/include/boards/" \
                          -I "$PICO_SDK_PATH/src/rp2040/hardware_regs/include/" \
                          -I "$PICO_SDK_PATH/src/rp2_common/pico_platform/include/" \
                          -I "$PICO_SDK_PATH/src/rp2_common/boot_stage2/asminclude/" \

tools/libpico/pico_extras_import.cmake

@@ -26,14 +26,14 @@ if (NOT PICO_EXTRAS_PATH)
             get_filename_component(FETCHCONTENT_BASE_DIR "${PICO_EXTRAS_FETCH_FROM_GIT_PATH}" REALPATH BASE_DIR "${CMAKE_SOURCE_DIR}")
         endif ()
         FetchContent_Declare(
-                PICO_EXTRAS
+                pico_extras
                 GIT_REPOSITORY https://github.com/raspberrypi/pico-extras
                 GIT_TAG master
         )
-        if (NOT PICO_EXTRAS)
-            message("Downloading PICO EXTRAS")
-            FetchContent_Populate(PICO_EXTRAS)
-            set(PICO_EXTRAS_PATH ${PICO_EXTRAS_SOURCE_DIR})
+        if (NOT pico_extras)
+            message("Downloading Raspberry Pi Pico Extras")
+            FetchContent_Populate(pico_extras)
+            set(PICO_EXTRAS_PATH ${pico_extras_SOURCE_DIR})
         endif ()
         set(FETCHCONTENT_BASE_DIR ${FETCHCONTENT_BASE_DIR_SAVE})
     else ()
@@ -59,4 +59,4 @@ endif ()
 
 set(PICO_EXTRAS_PATH ${PICO_EXTRAS_PATH} CACHE PATH "Path to the PICO EXTRAS" FORCE)
 
-add_subdirectory(${PICO_EXTRAS_PATH} pico_extras)
+add_subdirectory(${PICO_EXTRAS_PATH} pico_extras)

tools/libpico/pico_sdk_import.cmake

@@ -3,8 +3,6 @@
 # This can be dropped into an external project to help locate this SDK
 # It should be include()ed prior to project()
 
-# todo document
-
 if (DEFINED ENV{PICO_SDK_PATH} AND (NOT PICO_SDK_PATH))
     set(PICO_SDK_PATH $ENV{PICO_SDK_PATH})
     message("Using PICO_SDK_PATH from environment ('${PICO_SDK_PATH}')")
@@ -20,8 +18,8 @@ if (DEFINED ENV{PICO_SDK_FETCH_FROM_GIT_PATH} AND (NOT PICO_SDK_FETCH_FROM_GIT_P
     message("Using PICO_SDK_FETCH_FROM_GIT_PATH from environment ('${PICO_SDK_FETCH_FROM_GIT_PATH}')")
 endif ()
 
-set(PICO_SDK_PATH "${PICO_SDK_PATH}" CACHE PATH "Path to the PICO SDK")
-set(PICO_SDK_FETCH_FROM_GIT "${PICO_SDK_FETCH_FROM_GIT}" CACHE BOOL "Set to ON to fetch copy of PICO SDK from git if not otherwise locatable")
+set(PICO_SDK_PATH "${PICO_SDK_PATH}" CACHE PATH "Path to the Raspberry Pi Pico SDK")
+set(PICO_SDK_FETCH_FROM_GIT "${PICO_SDK_FETCH_FROM_GIT}" CACHE BOOL "Set to ON to fetch copy of SDK from git if not otherwise locatable")
 set(PICO_SDK_FETCH_FROM_GIT_PATH "${PICO_SDK_FETCH_FROM_GIT_PATH}" CACHE FILEPATH "location to download SDK")
 
 if (NOT PICO_SDK_PATH)
@@ -37,14 +35,14 @@ if (NOT PICO_SDK_PATH)
                 GIT_TAG master
         )
         if (NOT pico_sdk)
-            message("Downloading PICO SDK")
+            message("Downloading Raspberry Pi Pico SDK")
             FetchContent_Populate(pico_sdk)
             set(PICO_SDK_PATH ${pico_sdk_SOURCE_DIR})
         endif ()
         set(FETCHCONTENT_BASE_DIR ${FETCHCONTENT_BASE_DIR_SAVE})
     else ()
         message(FATAL_ERROR
-                "PICO SDK location was not specified. Please set PICO_SDK_PATH or set PICO_SDK_FETCH_FROM_GIT to on to fetch from git."
+                "SDK location was not specified. Please set PICO_SDK_PATH or set PICO_SDK_FETCH_FROM_GIT to on to fetch from git."
                 )
     endif ()
 endif ()
@@ -56,9 +54,9 @@ endif ()
 
 set(PICO_SDK_INIT_CMAKE_FILE ${PICO_SDK_PATH}/pico_sdk_init.cmake)
 if (NOT EXISTS ${PICO_SDK_INIT_CMAKE_FILE})
-    message(FATAL_ERROR "Directory '${PICO_SDK_PATH}' does not appear to contain the PICO SDK")
+    message(FATAL_ERROR "Directory '${PICO_SDK_PATH}' does not appear to contain the Raspberry Pi Pico SDK")
 endif ()
 
-set(PICO_SDK_PATH ${PICO_SDK_PATH} CACHE PATH "Path to the PICO SDK" FORCE)
+set(PICO_SDK_PATH ${PICO_SDK_PATH} CACHE PATH "Path to the Raspberry Pi Pico SDK" FORCE)
 
 include(${PICO_SDK_INIT_CMAKE_FILE})

tools/makeboards.py

@@ -66,7 +66,7 @@ def BuildWithoutUSBStack(name):
     print("%s.menu.usbstack.nousb=No USB" % (name))
     print('%s.menu.usbstack.nousb.build.usbstack_flags="-DNO_USB -DDISABLE_USB_SERIAL -I{runtime.platform.path}/tools/libpico"' % (name))
 
-def BuildHeader(name, vendor_name, product_name, vidtouse, pidtouse, vid, pid, boarddefine, variant, uploadtool, flashsize, ramsize, boot2):
+def BuildHeader(name, vendor_name, product_name, vidtouse, pidtouse, vid, pid, pwr, boarddefine, variant, uploadtool, flashsize, ramsize, boot2):
     prettyname = vendor_name + " " + product_name
     print()
     print("# -----------------------------------")
@@ -76,6 +76,7 @@ def BuildHeader(name, vendor_name, product_name, vidtouse, pidtouse, vid, pid, b
     print("%s.vid.0=%s" % (name, vidtouse))
     print("%s.pid.0=%s" % (name, pidtouse))
     print("%s.build.usbpid=-DSERIALUSB_PID=%s" % (name, pid))
+    print("%s.build.usbpwr=-DUSBD_MAX_POWER_MA=%s" % (name, pwr))
     print("%s.build.board=%s" % (name, boarddefine))
     print("%s.build.mcu=cortex-m0plus" % (name))
     print("%s.build.variant=%s" % (name, variant))
@@ -89,7 +90,6 @@ def BuildHeader(name, vendor_name, product_name, vidtouse, pidtouse, vid, pid, b
     print("%s.build.f_cpu=125000000" % (name))
     print("%s.build.led=" % (name))
     print("%s.build.core=rp2040" % (name))
-    print("%s.build.mcu=rp2040" % (name))
     print("%s.build.ldscript=memmap_default.ld" % (name))
     print("%s.build.ram_length=%dk" % (name, ramsize / 1024))
     print("%s.build.boot2=%s" % (name, boot2))
@@ -98,6 +98,12 @@ def BuildHeader(name, vendor_name, product_name, vidtouse, pidtouse, vid, pid, b
     print('%s.build.usb_manufacturer="%s"' % (name, vendor_name))
     print('%s.build.usb_product="%s"' % (name, product_name))
 
+def WriteWarning():
+    print("# WARNING - DO NOT EDIT THIS FILE, IT IS MACHINE GENERATED")
+    print("#           To change something here, edit tools/makeboards.py and")
+    print("#           run 'python3 makeboards.py > ../boards.txt' to regenerate")
+    print()
+
 def BuildGlobalMenuList():
     print("menu.BoardModel=Model")
     print("menu.flash=Flash Size")
@@ -110,7 +116,7 @@ def BuildGlobalMenuList():
     print("menu.usbstack=USB Stack")
 
 
-def MakeBoard(name, vendor_name, product_name, vid, pid, boarddefine, flashsizemb, boot2):
+def MakeBoard(name, vendor_name, product_name, vid, pid, pwr, boarddefine, flashsizemb, boot2):
     for a, b, c in [ ["", "", "uf2conv"], ["picoprobe", " (Picoprobe)", "picoprobe"], ["picodebug", " (pico-debug)", "picodebug"]]:
         n = name + a
         p = product_name + b
@@ -127,7 +133,7 @@ def MakeBoard(name, vendor_name, product_name, vid, pid, boarddefine, flashsizem
             ramsizekb = 240;
         else:
             pidtouse = pid
-        BuildHeader(n, vendor_name, p, vidtouse, pidtouse, vid, pid, boarddefine, name, c, flashsizemb * 1024 * 1024, ramsizekb * 1024, boot2)
+        BuildHeader(n, vendor_name, p, vidtouse, pidtouse, vid, pid, pwr, boarddefine, name, c, flashsizemb * 1024 * 1024, ramsizekb * 1024, boot2)
         if name == "generic":
             BuildFlashMenu(n, 2*1024*1024, [0, 1*1024*1024])
             BuildFlashMenu(n, 4*1024*1024, [0, 2*1024*1024])
@@ -147,21 +153,24 @@ def MakeBoard(name, vendor_name, product_name, vid, pid, boarddefine, flashsizem
         if name == "generic":
             BuildBoot(n)
 
-
+WriteWarning()
 BuildGlobalMenuList()
-MakeBoard("rpipico", "Raspberry Pi", "Pico", "0x2e8a", "0x000a", "RASPBERRY_PI_PICO", 2, "boot2_w25q080_2_padded_checksum")
-MakeBoard("adafruit_feather", "Adafruit", "Feather RP2040", "0x239a", "0x80f1", "ADAFRUIT_FEATHER_RP2040", 8, "boot2_w25x10cl_4_padded_checksum")
-MakeBoard("adafruit_itsybitsy", "Adafruit", "ItsyBitsy RP2040", "0x239a", "0x80fd", "ADAFRUIT_ITSYBITSY_RP2040", 8, "boot2_w25q080_2_padded_checksum")
-MakeBoard("adafruit_qtpy", "Adafruit", "QT Py RP2040", "0x239a", "0x80f7", "ADAFRUIT_QTPY_RP2040", 8, "boot2_w25q080_2_padded_checksum")
-MakeBoard("adafruit_stemmafriend", "Adafruit", "STEMMA Friend RP2040", "0x239a", "0x80e3", "ADAFRUIT_STEMMAFRIEND_RP2040", 8, "boot2_w25q080_2_padded_checksum")
-MakeBoard("adafruit_trinkeyrp2040qt", "Adafruit", "Trinkey RP2040 QT", "0x239a", "0x8109", "ADAFRUIT_TRINKEYQT_RP2040", 8, "boot2_w25q080_2_padded_checksum")
-MakeBoard("adafruit_macropad2040", "Adafruit", "MacroPad RP2040", "0x239a", "0x8107", "ADAFRUIT_MACROPAD_RP2040", 8, "boot2_w25q080_2_padded_checksum")
-MakeBoard("arduino_nano_connect", "Arduino", "Nano RP2040 Connect", "0x2341", "0x0058", "ARDUINO_NANO_RP2040_CONNECT", 16, "boot2_w25q080_2_padded_checksum")
-MakeBoard("cytron_maker_pi_rp2040", "Cytron", "Maker Pi RP2040", "0x2e8a", "0x1000", "CYTRON_MAKER_PI_RP2040", 2, "boot2_w25q080_2_padded_checksum")
-MakeBoard("sparkfun_promicrorp2040", "SparkFun", "ProMicro RP2040", "0x1b4f", "0x0026", "SPARKFUN_PROMICRO_RP2040", 16, "boot2_generic_03h_4_padded_checksum")
-MakeBoard("generic", "Generic", "RP2040", "0x2e8a", "0xf00a", "GENERIC_RP2040", 16, "boot2_generic_03h_4_padded_checksum")
-MakeBoard("challenger_2040_wifi", "iLabs", "Challenger 2040 WiFi", "0x2e8a", "0x1006", "CHALLENGER_2040_WIFI_RP2040", 8, "boot2_w25q080_2_padded_checksum")
-MakeBoard("challenger_2040_lte", "iLabs", "Challenger 2040 LTE", "0x2e8a", "0x100b", "CHALLENGER_2040_LTE_RP2040", 8, "boot2_w25q080_2_padded_checksum")
-MakeBoard("melopero_shake_rp2040", "Melopero", "Shake RP2040", "0x2e8a", "0x1005", "MELOPERO_SHAKE_RP2040", 16, "boot2_w25q080_2_padded_checksum")
-MakeBoard("upesy_rp2040_devkit", "uPesy", "RP2040 DevKit", "0x2e8a", "0x1007", "UPESY_RP2040_DEVKIT", 2, "boot2_w25q080_2_padded_checksum")
-MakeBoard("wiznet_5100s_evb_pico", "WIZnet", "W5100S-EVB-Pico", "0x2e8a", "0x1008", "WIZNET_5100S_EVB_PICO", 2, "boot2_w25q080_2_padded_checksum")
+MakeBoard("rpipico", "Raspberry Pi", "Pico", "0x2e8a", "0x000a", 250, "RASPBERRY_PI_PICO", 2, "boot2_w25q080_2_padded_checksum")
+MakeBoard("adafruit_feather", "Adafruit", "Feather RP2040", "0x239a", "0x80f1", 250, "ADAFRUIT_FEATHER_RP2040", 8, "boot2_w25x10cl_4_padded_checksum")
+MakeBoard("adafruit_itsybitsy", "Adafruit", "ItsyBitsy RP2040", "0x239a", "0x80fd", 250, "ADAFRUIT_ITSYBITSY_RP2040", 8, "boot2_w25q080_2_padded_checksum")
+MakeBoard("adafruit_qtpy", "Adafruit", "QT Py RP2040", "0x239a", "0x80f7", 250, "ADAFRUIT_QTPY_RP2040", 8, "boot2_w25q080_2_padded_checksum")
+MakeBoard("adafruit_stemmafriend", "Adafruit", "STEMMA Friend RP2040", "0x239a", "0x80e3", 250, "ADAFRUIT_STEMMAFRIEND_RP2040", 8, "boot2_w25q080_2_padded_checksum")
+MakeBoard("adafruit_trinkeyrp2040qt", "Adafruit", "Trinkey RP2040 QT", "0x239a", "0x8109", 250, "ADAFRUIT_TRINKEYQT_RP2040", 8, "boot2_w25q080_2_padded_checksum")
+MakeBoard("adafruit_macropad2040", "Adafruit", "MacroPad RP2040", "0x239a", "0x8107", 250, "ADAFRUIT_MACROPAD_RP2040", 8, "boot2_w25q080_2_padded_checksum")
+MakeBoard("arduino_nano_connect", "Arduino", "Nano RP2040 Connect", "0x2341", "0x0058", 250, "ARDUINO_NANO_RP2040_CONNECT", 16, "boot2_w25q080_2_padded_checksum")
+MakeBoard("cytron_maker_nano_rp2040", "Cytron", "Maker Nano RP2040", "0x2e8a", "0x100f", 250, "CYTRON_MAKER_NANO_RP2040", 2, "boot2_w25q080_2_padded_checksum")
+MakeBoard("cytron_maker_pi_rp2040", "Cytron", "Maker Pi RP2040", "0x2e8a", "0x1000", 250, "CYTRON_MAKER_PI_RP2040", 2, "boot2_w25q080_2_padded_checksum")
+MakeBoard("sparkfun_promicrorp2040", "SparkFun", "ProMicro RP2040", "0x1b4f", "0x0026", 250, "SPARKFUN_PROMICRO_RP2040", 16, "boot2_generic_03h_4_padded_checksum")
+MakeBoard("generic", "Generic", "RP2040", "0x2e8a", "0xf00a", 250, "GENERIC_RP2040", 16, "boot2_generic_03h_4_padded_checksum")
+MakeBoard("challenger_2040_wifi", "iLabs", "Challenger 2040 WiFi", "0x2e8a", "0x1006", 250, "CHALLENGER_2040_WIFI_RP2040", 8, "boot2_w25q080_2_padded_checksum")
+MakeBoard("challenger_2040_lte", "iLabs", "Challenger 2040 LTE", "0x2e8a", "0x100b", 500, "CHALLENGER_2040_LTE_RP2040", 8, "boot2_w25q080_2_padded_checksum")
+MakeBoard("challenger_nb_2040_wifi", "iLabs", "Challenger NB 2040 WiFi", "0x2e8a", "0x100b", 500, "CHALLENGER_NB_2040_WIFI_RP2040", 8, "boot2_w25q080_2_padded_checksum")
+MakeBoard("ilabs_rpico32", "iLabs", "RPICO32", "0x2e8a", "0x1010", 250, "ILABS_2040_RPICO32_RP2040", 8, "boot2_w25q080_2_padded_checksum")
+MakeBoard("melopero_shake_rp2040", "Melopero", "Shake RP2040", "0x2e8a", "0x1005", 250, "MELOPERO_SHAKE_RP2040", 16, "boot2_w25q080_2_padded_checksum")
+MakeBoard("upesy_rp2040_devkit", "uPesy", "RP2040 DevKit", "0x2e8a", "0x1007", 250, "UPESY_RP2040_DEVKIT", 2, "boot2_w25q080_2_padded_checksum")
+MakeBoard("wiznet_5100s_evb_pico", "WIZnet", "W5100S-EVB-Pico", "0x2e8a", "0x1008", 250, "WIZNET_5100S_EVB_PICO", 2, "boot2_w25q080_2_padded_checksum")

variants/challenger_2040_lte/ChallengerLTE.cpp

@@ -0,0 +1,133 @@
+/*
+    UBlox SARA helper class for the Challenger RP2040 LTE boards
+
+    Copyright (c) 2021 P. Oldberg <pontus@ilabs.se>
+
+    This library is free software; you can redistribute it and/or
+    modify it under the terms of the GNU Lesser General Public
+    License as published by the Free Software Foundation; either
+    version 2.1 of the License, or (at your option) any later version.
+
+    This library is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+    Lesser General Public License for more details.
+
+    You should have received a copy of the GNU Lesser General Public
+    License along with this library; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#include <Arduino.h>
+#include <ChallengerLTE.h>
+
+Challenger2040LTEClass::Challenger2040LTEClass() {
+  pinMode(PIN_SARA_ON, OUTPUT);
+  digitalWrite(PIN_SARA_ON, LOW);           // Output register must always be low
+  pinMode(PIN_SARA_ON, INPUT_PULLUP);
+
+  pinMode(PIN_SARA_RST, INPUT_PULLUP);      // Keep as input for now
+
+  pinMode(PIN_SARA_PWR, OUTPUT);
+  digitalWrite(PIN_SARA_PWR, LOW);          // No power to SARA yet
+  serialPortConfigured = false;
+}
+
+// Do a HW reset by applying a low pulse to the reset line for 1mSec
+bool Challenger2040LTEClass::doPowerOn() {
+  bool ret;
+  digitalWrite(PIN_SARA_PWR, HIGH);         // Make sure LDO is on
+  delay(100);                               // let the power stabilize
+  pinMode(PIN_SARA_ON, OUTPUT);             // Pull power on control low
+  delay(150);                               // For 150mS
+  pinMode(PIN_SARA_ON, INPUT_PULLUP);       // before releasing it again.
+  delay(1000);                              // Now wait for 1 second
+  SARA_SERIAL_PORT.begin(DEFAULT_SARA_BAUDRATE);
+  serialPortConfigured = true;
+  ret = isAlive();                          // Makie sure the modem is
+                                            // up and running
+
+  delay(250);                               // Allow for any extra characters
+  // before flushing the input buffer
+  while(SARA_SERIAL_PORT.available()) SARA_SERIAL_PORT.read();
+
+  return ret;
+}
+
+// Checks to see if the modem responds to the "AT" poll command.
+bool Challenger2040LTEClass::isAlive(uint32_t timeout) {
+  SARA_SERIAL_PORT.setTimeout(100);
+  SARA_SERIAL_PORT.println(F("AT"));
+  String rdy = SARA_SERIAL_PORT.readStringUntil('\n');
+  while(!rdy.startsWith(F("OK")) && --timeout) {
+    SARA_SERIAL_PORT.println(F("AT"));
+    rdy = SARA_SERIAL_PORT.readStringUntil('\n');
+    //Serial.println(rdy);
+  }
+  SARA_SERIAL_PORT.setTimeout(1000);      // Restore serial timeout
+  if (timeout)
+    return true;
+  return false;
+}
+
+// Return the current MNO profile
+// Returns -1 if the serial port is not yet setup or the number of the current
+// MNO profile setting from the modem.
+int Challenger2040LTEClass::getMNOProfile() {
+  if (!serialPortConfigured)
+    return -1;
+  SARA_SERIAL_PORT.println(F("AT+UMNOPROF?"));
+  String resp = getResponse();
+  return resp.substring(resp.indexOf("+UMNOPROF: ") + 11).toInt();
+}
+
+// Set a new MNO profile
+// Returns false if the serial port is not yet setup
+bool Challenger2040LTEClass::setMNOProfile(int profile) {
+  if (!serialPortConfigured)
+    return false;
+  String cmd = "AT+UMNOPROF=" + String(profile) + ",1";
+  SARA_SERIAL_PORT.println(cmd);
+
+  if (!getResponse().endsWith("OK")) {
+    return false;
+  }
+  return true;
+}
+
+// Disable power save features
+bool Challenger2040LTEClass::enablePS(bool enable) {
+  if (!serialPortConfigured)
+    return false;
+  if (enable)
+    SARA_SERIAL_PORT.println(F("AT+CPSMS=1"));
+  else
+    SARA_SERIAL_PORT.println(F("AT+CPSMS=0"));
+
+  if (!getResponse().endsWith("OK")) {
+    return false;
+  }
+  return true;
+}
+
+// Get a response from SARA
+// A default serial timeout of 2 seconds allow for reading really slow
+// responses which should accommodate most replies. Replies are then trimmed
+// from control characters and appended with a tab character as a separator.
+//
+String Challenger2040LTEClass::getResponse(int timeout) {
+  SARA_SERIAL_PORT.setTimeout(2000);            // allow for really slow responses
+
+  String resp = SARA_SERIAL_PORT.readStringUntil('\n');
+  resp.trim();
+  String acc = resp;
+  while(resp.indexOf("OK") == -1 && resp.indexOf("ERROR") == -1 && --timeout) {
+    resp = SARA_SERIAL_PORT.readStringUntil('\n');
+    resp.trim();
+    if (resp.length())
+      acc += "\t" + resp;
+  }
+  return acc;
+}
+
+Challenger2040LTEClass Challenger2040LTE;

variants/challenger_2040_lte/ChallengerLTE.h

@@ -0,0 +1,38 @@
+/*
+    UBlox SARA helper class for the Challenger RP2040 LTE boards
+
+    Copyright (c) 2021 P. Oldberg <pontus@ilabs.se>
+
+    This library is free software; you can redistribute it and/or
+    modify it under the terms of the GNU Lesser General Public
+    License as published by the Free Software Foundation; either
+    version 2.1 of the License, or (at your option) any later version.
+
+    This library is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+    Lesser General Public License for more details.
+
+    You should have received a copy of the GNU Lesser General Public
+    License along with this library; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+#pragma once
+
+#define DEFAULT_SARA_BAUDRATE      115200
+
+class Challenger2040LTEClass {
+  public:
+    Challenger2040LTEClass();
+    bool doPowerOn();
+    bool isAlive(uint32_t timeout = 50);
+    int getMNOProfile();
+    bool setMNOProfile(int profile);
+    bool enablePS(bool enable = true);
+    String getResponse(int timeout = 5);
+
+  private:
+    bool serialPortConfigured;
+};
+
+extern Challenger2040LTEClass Challenger2040LTE;

variants/challenger_2040_lte/pins_arduino.h

@@ -21,6 +21,7 @@
 #define PIN_SARA_ON         (13u)
 #define PIN_SARA_RST        (14u)
 #define PIN_SARA_PWR        (15u)
+#define SARA_SERIAL_PORT    Serial2
 
 // SPI
 #define PIN_SPI0_MISO       (24u)

variants/challenger_nb_2040_wifi/ChallengerWiFi.cpp

@@ -0,0 +1,107 @@
+/*
+    ESP8285 helper class for the Challenger RP2040 WiFi boards
+
+    Copyright (c) 2021 P. Oldberg <pontus@ilabs.se>
+
+    This library is free software; you can redistribute it and/or
+    modify it under the terms of the GNU Lesser General Public
+    License as published by the Free Software Foundation; either
+    version 2.1 of the License, or (at your option) any later version.
+
+    This library is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+    Lesser General Public License for more details.
+
+    You should have received a copy of the GNU Lesser General Public
+    License along with this library; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#include <Arduino.h>
+#include <ChallengerWiFi.h>
+
+Challenger2040WiFiClass::Challenger2040WiFiClass() {
+  pinMode(PIN_ESP8285_RST, OUTPUT);
+  digitalWrite(PIN_ESP8285_RST, LOW);       // Hold ESP8285 in reset
+  pinMode(PIN_ESP8285_MODE, OUTPUT);
+  digitalWrite(PIN_ESP8285_MODE, HIGH);     // Prepare for normal start
+}
+
+// Do a HW reset by applying a low pulse to the reset line for 1mSec
+void Challenger2040WiFiClass::doHWReset() {
+  digitalWrite(PIN_ESP8285_RST, LOW);       // Hold ESP8285 in reset
+  delay(1);
+  digitalWrite(PIN_ESP8285_RST, HIGH);      // Release ESP8285 reset
+}
+
+// Set the mode flag high to indicate normal run operation and do a HW
+// reset.
+void Challenger2040WiFiClass::runReset() {  // Prepare ESP8285 for normal op
+  digitalWrite(PIN_ESP8285_MODE, HIGH);     // Prepare for normal start
+  doHWReset();
+}
+
+// Set the mode flag low to indicate flash operation and do a HW
+// reset.
+void Challenger2040WiFiClass::flashReset() { // Prepare ESP8285 for flashing
+  digitalWrite(PIN_ESP8285_MODE, LOW);       // Prepare for normal start
+  doHWReset();
+}
+
+// Wait for the modem to reply with a "ready" prompt. This can be done
+// after a sw or hw reset have been performed to ensure that the AT
+// interpreter is up and running.
+bool Challenger2040WiFiClass::waitForReady() {
+  int timeout = 20;                         // Aprox max 2 sec
+
+  Serial2.begin(DEFAULT_ESP8285_BAUDRATE);
+  Serial2.setTimeout(100);
+  String rdy = Serial2.readStringUntil('\n');
+  while(!rdy.startsWith("ready") && timeout--) {
+    rdy = Serial2.readStringUntil('\n');
+  }
+  Serial2.setTimeout(1000);  // Reset default timeout to 1000
+  if (timeout)
+    return true;
+  return false;
+}
+
+// Reset the ESP8285 and wait for the "ready" prompt to be returned.
+bool Challenger2040WiFiClass::reset() {
+  runReset();
+  return waitForReady();
+}
+
+// Checks to see if the modem responds to the "AT" poll command.
+bool Challenger2040WiFiClass::isAlive() {
+  int timeout = 5;
+
+  Serial2.setTimeout(250);
+  Serial2.println(F("AT"));
+  String rdy = Serial2.readStringUntil('\n');
+  while(!rdy.startsWith(F("OK")) && timeout--) {
+    rdy = Serial2.readStringUntil('\n');
+  }
+  Serial2.setTimeout(1000);
+
+  if (timeout)
+    return true;
+  return false;
+}
+
+// Change the baud rate of the ESP8285 as well as the local UART.
+// No checking is done on the input baud rate so the user must know what
+// baud rates are valid. The function ends by checking if the ESP8285 is
+// reachable by doing an "AT" poll.
+bool Challenger2040WiFiClass::changeBaudRate(int baud) {
+  Serial2.print(F("AT+UART_CUR="));
+  Serial2.print(baud);
+  Serial2.println(F(",8,1,0,0"));
+  delay(100);
+  Serial2.end();
+  Serial2.begin(baud);
+  return isAlive();
+}
+
+Challenger2040WiFiClass Challenger2040WiFi;

variants/challenger_nb_2040_wifi/ChallengerWiFi.h

@@ -0,0 +1,36 @@
+/*
+    ESP8285 helper class for the Challenger RP2040 WiFi boards
+
+    Copyright (c) 2021 P. Oldberg <pontus@ilabs.se>
+
+    This library is free software; you can redistribute it and/or
+    modify it under the terms of the GNU Lesser General Public
+    License as published by the Free Software Foundation; either
+    version 2.1 of the License, or (at your option) any later version.
+
+    This library is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+    Lesser General Public License for more details.
+
+    You should have received a copy of the GNU Lesser General Public
+    License along with this library; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+#pragma once
+
+#define DEFAULT_ESP8285_BAUDRATE      115200
+
+class Challenger2040WiFiClass {
+  public:
+    Challenger2040WiFiClass();
+    void doHWReset();
+    void runReset();
+    void flashReset();
+    bool waitForReady();
+    bool reset();
+    bool isAlive();
+    bool changeBaudRate(int baud);
+};
+
+extern Challenger2040WiFiClass Challenger2040WiFi;

variants/challenger_nb_2040_wifi/pins_arduino.h

@@ -0,0 +1,75 @@
+#pragma once
+
+#include <ChallengerWiFi.h>
+
+#define PINS_COUNT          (24u)
+#define NUM_DIGITAL_PINS    (24u)
+#define NUM_ANALOG_INPUTS   (4u)
+#define NUM_ANALOG_OUTPUTS  (0u)
+#define ADC_RESOLUTION      (12u)
+
+// LEDs
+#define PIN_LED             (12u)
+
+// Serial
+#define PIN_SERIAL1_TX      (16u)
+#define PIN_SERIAL1_RX      (17u)
+
+// Connected to ESP8285
+#define PIN_SERIAL2_TX      (4u)
+#define PIN_SERIAL2_RX      (5u)
+#define PIN_ESP8285_RST     (19u)
+#define PIN_ESP8285_MODE    (13u)
+
+// SPI
+#define PIN_SPI0_MISO       (24u)
+#define PIN_SPI0_MOSI       (23u)
+#define PIN_SPI0_SCK        (22u)
+#define PIN_SPI0_SS         (21u)
+
+// Not pinned out
+#define PIN_SPI1_MISO       (31u)
+#define PIN_SPI1_MOSI       (31u)
+#define PIN_SPI1_SCK        (31u)
+#define PIN_SPI1_SS         (31u)
+
+// Wire
+#define PIN_WIRE0_SDA       (0u)
+#define PIN_WIRE0_SCL       (1u)
+
+// Not pinned out
+#define PIN_WIRE1_SDA       (31u)
+#define PIN_WIRE1_SCL       (31u)
+
+#define SERIAL_HOWMANY      (2u)
+#define SPI_HOWMANY         (1u)
+#define WIRE_HOWMANY        (1u)
+
+#define LED_BUILTIN         PIN_LED
+#define NEOPIXEL            (11u)
+
+static const uint8_t D0 =   (16u);
+static const uint8_t D1 =   (17u);
+static const uint8_t D2 =   (24u);
+static const uint8_t D3 =   (23u);
+static const uint8_t D4 =   (22u);
+static const uint8_t D5 =   (2u);
+static const uint8_t D6 =   (3u);
+static const uint8_t D7 =   (0u);
+static const uint8_t D8 =   (1u);
+static const uint8_t D9 =   (6u);
+static const uint8_t D10 =  (7u);
+static const uint8_t D11 =  (8u);
+static const uint8_t D12 =  (9u);
+static const uint8_t D13 = (10u);
+static const uint8_t D14 = (14u);
+static const uint8_t D15 = (15u);
+static const uint8_t D16 = (18u);
+static const uint8_t D17 = (20u);
+
+static const uint8_t A0 = (26u);
+static const uint8_t A1 = (27u);
+static const uint8_t A2 = (28u);
+static const uint8_t A3 = (29u);
+static const uint8_t A4 = (25u);
+static const uint8_t A5 = (21u);

variants/cytron_maker_nano_rp2040/pins_arduino.h

@@ -0,0 +1,52 @@
+#pragma once
+
+// LEDs
+#define PIN_LED             (2u)
+
+// Neopixel
+#define PIN_NEOPIXEL        (11u)
+#define NUM_NEOPIXEL        (2u)
+#define PIN_RGB             PIN_NEOPIXEL
+
+// Buzzer
+#define PIN_BUZZER          (22u)
+
+// Button
+#define PIN_BUTTON			(20u)
+
+
+
+// Serial 1
+#define PIN_SERIAL1_TX      (0u)
+#define PIN_SERIAL1_RX      (1u)
+
+// Serial 2 (Not pinned out)
+#define PIN_SERIAL2_TX      (31u)
+#define PIN_SERIAL2_RX      (31u)
+
+// SPI 0
+#define PIN_SPI0_MISO       (16u)
+#define PIN_SPI0_MOSI       (19u)
+#define PIN_SPI0_SCK        (18u)
+#define PIN_SPI0_SS         (17u)
+
+// SPI 1 (Not pinned out)
+#define PIN_SPI1_MISO       (31u)
+#define PIN_SPI1_MOSI       (31u)
+#define PIN_SPI1_SCK        (31u)
+#define PIN_SPI1_SS         (31u)
+
+// Wire
+#define PIN_WIRE0_SDA       (0u)
+#define PIN_WIRE0_SCL       (1u)
+
+#define PIN_WIRE1_SDA       (26u)
+#define PIN_WIRE1_SCL       (27u)
+
+
+
+#define SERIAL_HOWMANY      (1u)
+#define SPI_HOWMANY         (1u)
+#define WIRE_HOWMANY        (2u)
+
+#include "../generic/common.h"

variants/ilabs_rpico32/Ilabs2040WiFiClass.cpp

@@ -0,0 +1,107 @@
+/*
+    ESP8285 helper class for the Challenger RP2040 WiFi boards
+
+    Copyright (c) 2021 P. Oldberg <pontus@ilabs.se>
+
+    This library is free software; you can redistribute it and/or
+    modify it under the terms of the GNU Lesser General Public
+    License as published by the Free Software Foundation; either
+    version 2.1 of the License, or (at your option) any later version.
+
+    This library is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+    Lesser General Public License for more details.
+
+    You should have received a copy of the GNU Lesser General Public
+    License along with this library; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#include <Arduino.h>
+#include <Ilabs2040WiFiClass.h>
+
+Ilabs2040WiFiClass::Ilabs2040WiFiClass() {
+  pinMode(PIN_ESP_RESET, OUTPUT);
+  digitalWrite(PIN_ESP_RESET, LOW);     // Hold ESP8285 in reset
+  pinMode(PIN_ESP_MODE, OUTPUT);
+  digitalWrite(PIN_ESP_MODE, HIGH);     // Prepare for normal start
+}
+
+// Do a HW reset by applying a low pulse to the reset line for 1mSec
+void Ilabs2040WiFiClass::doHWReset() {
+  digitalWrite(PIN_ESP_RESET, LOW);     // Hold ESP8285 in reset
+  delay(1);
+  digitalWrite(PIN_ESP_RESET, HIGH);    // Release ESP8285 reset
+}
+
+// Set the mode flag high to indicate normal run operation and do a HW
+// reset.
+void Ilabs2040WiFiClass::runReset() {   // Prepare ESP8285 for normal op
+  digitalWrite(PIN_ESP_MODE, HIGH);     // Prepare for normal start
+  doHWReset();
+}
+
+// Set the mode flag low to indicate flash operation and do a HW
+// reset.
+void Ilabs2040WiFiClass::flashReset() { // Prepare ESP8285 for flashing
+  digitalWrite(PIN_ESP_MODE, LOW);      // Prepare for normal start
+  doHWReset();
+}
+
+// Wait for the modem to reply with a "ready" prompt. This can be done
+// after a sw or hw reset have been performed to ensure that the AT
+// interpreter is up and running.
+bool Ilabs2040WiFiClass::waitForReady() {
+  int timeout = 20;                     // Aprox max 2 sec
+
+  ESP_SERIAL_PORT.begin(DEFAULT_ESP8285_BAUDRATE);
+  ESP_SERIAL_PORT.setTimeout(100);
+  String rdy = ESP_SERIAL_PORT.readStringUntil('\n');
+  while(!rdy.startsWith("ready") && timeout--) {
+    rdy = ESP_SERIAL_PORT.readStringUntil('\n');
+  }
+  ESP_SERIAL_PORT.setTimeout(1000);   // Reset default timeout to 1000
+  if (timeout)
+    return true;
+  return false;
+}
+
+// Reset the ESP8285 and wait for the "ready" prompt to be returned.
+bool Ilabs2040WiFiClass::reset() {
+  runReset();
+  return waitForReady();
+}
+
+// Checks to see if the modem responds to the "AT" poll command.
+bool Ilabs2040WiFiClass::isAlive() {
+  int timeout = 5;
+
+  ESP_SERIAL_PORT.setTimeout(250);
+  ESP_SERIAL_PORT.println(F("AT"));
+  String rdy = ESP_SERIAL_PORT.readStringUntil('\n');
+  while(!rdy.startsWith(F("OK")) && timeout--) {
+    rdy = ESP_SERIAL_PORT.readStringUntil('\n');
+  }
+  ESP_SERIAL_PORT.setTimeout(1000);
+
+  if (timeout)
+    return true;
+  return false;
+}
+
+// Change the baud rate of the ESP8285 as well as the local UART.
+// No checking is done on the input baud rate so the user must know what
+// baud rates are valid. The function ends by checking if the ESP8285 is
+// reachable by doing an "AT" poll.
+bool Ilabs2040WiFiClass::changeBaudRate(int baud) {
+  ESP_SERIAL_PORT.print(F("AT+UART_CUR="));
+  ESP_SERIAL_PORT.print(baud);
+  ESP_SERIAL_PORT.println(F(",8,1,0,0"));
+  delay(100);
+  ESP_SERIAL_PORT.end();
+  ESP_SERIAL_PORT.begin(baud);
+  return isAlive();
+}
+
+Ilabs2040WiFiClass Ilabs2040WiFi;

variants/ilabs_rpico32/Ilabs2040WiFiClass.h

@@ -0,0 +1,36 @@
+/*
+    ESP8285 helper class for the Challenger RP2040 WiFi boards
+
+    Copyright (c) 2021 P. Oldberg <pontus@ilabs.se>
+
+    This library is free software; you can redistribute it and/or
+    modify it under the terms of the GNU Lesser General Public
+    License as published by the Free Software Foundation; either
+    version 2.1 of the License, or (at your option) any later version.
+
+    This library is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+    Lesser General Public License for more details.
+
+    You should have received a copy of the GNU Lesser General Public
+    License along with this library; if not, write to the Free Software
+    Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+#pragma once
+
+#define DEFAULT_ESP8285_BAUDRATE      115200
+
+class Ilabs2040WiFiClass {
+  public:
+    Ilabs2040WiFiClass();
+    void doHWReset();
+    void runReset();
+    void flashReset();
+    bool waitForReady();
+    bool reset();
+    bool isAlive();
+    bool changeBaudRate(int baud);
+};
+
+extern Ilabs2040WiFiClass Ilabs2040WiFi;

variants/ilabs_rpico32/pins_arduino.h

@@ -0,0 +1,82 @@
+#pragma once
+
+#include <Ilabs2040WiFiClass.h>
+
+#define PINS_COUNT          (26u)
+#define NUM_DIGITAL_PINS    (26u)
+#define NUM_ANALOG_INPUTS   (4u)
+#define NUM_ANALOG_OUTPUTS  (0u)
+#define ADC_RESOLUTION      (12u)
+
+// Connected to ESP8285
+#define PIN_SERIAL1_TX      (0u)
+#define PIN_SERIAL1_RX      (1u)
+#define PIN_ESP_RESET       (2u)
+#define PIN_ESP_MODE        (3u)
+#define PIN_ESP_TXD         PIN_SERIAL1_TX
+#define PIN_ESP_RXD         PIN_SERIAL1_RX
+#define ESP_SERIAL_PORT     Serial1
+
+// Serial
+#define PIN_SERIAL2_TX      (8u)
+#define PIN_SERIAL2_RX      (9u)
+
+// SPI
+#define PIN_SPI0_MISO       (24u)
+#define PIN_SPI0_MOSI       (23u)
+#define PIN_SPI0_SCK        (22u)
+#define PIN_SPI0_SS         (21u)
+
+// Not pinned out
+#define PIN_SPI1_MISO       (31u)
+#define PIN_SPI1_MOSI       (31u)
+#define PIN_SPI1_SCK        (31u)
+#define PIN_SPI1_SS         (31u)
+
+// Wire
+#define PIN_WIRE0_SDA       (4u)
+#define PIN_WIRE0_SCL       (5u)
+
+// Not pinned out
+#define PIN_WIRE1_SDA       (31u)
+#define PIN_WIRE1_SCL       (31u)
+
+#define SERIAL_HOWMANY      (2u)
+#define SPI_HOWMANY         (1u)
+#define WIRE_HOWMANY        (1u)
+
+static const uint8_t D0 = (0u);     // Internal to the board
+static const uint8_t D1 = (1u);     // Internal to the board
+static const uint8_t D2 = (2u);     // Internal to the board
+static const uint8_t D3 = (3u);     // Internal to the board
+static const uint8_t D4 = (4u);
+static const uint8_t D5 = (5u);
+static const uint8_t D6 = (6u);
+static const uint8_t D7 = (7u);
+static const uint8_t D8 = (8u);
+static const uint8_t D9 = (9u);
+static const uint8_t D10 = (10u);
+static const uint8_t D11 = (11u);
+static const uint8_t D12 = (12u);
+static const uint8_t D13 = (13u);
+static const uint8_t D14 = (14u);
+static const uint8_t D15 = (15u);
+static const uint8_t D16 = (16u);
+static const uint8_t D17 = (17u);
+static const uint8_t D18 = (18u);
+static const uint8_t D19 = (19u);
+static const uint8_t D20 = (20u);
+static const uint8_t D21 = (21u);
+static const uint8_t D22 = (22u);
+static const uint8_t D23 = (23u);
+static const uint8_t D24 = (24u);
+static const uint8_t D25 = (25u);
+static const uint8_t D26 = (26u);
+static const uint8_t D27 = (27u);
+static const uint8_t D28 = (28u);
+static const uint8_t D29 = (29u);
+
+static const uint8_t A0 = (26u);
+static const uint8_t A1 = (27u);
+static const uint8_t A2 = (28u);
+static const uint8_t A3 = (29u);