diy guide
CrazyRedMachine
@@ -0,0 +1,163 @@
|
||||
[](https://www.paypal.com/donate?hosted_button_id=WT735CX4UMZ9U)
|
||||
|
||||
# BEMANI PSX Adapter - DIY Adapter Tutorial
|
||||
|
||||
USB Adapter for Playstation IIDX and Pop'n Music Controllers.
|
||||
|
||||
Here's a step-by-step guide on how I used to make them
|
||||
|
||||
## Required materials
|
||||
|
||||
### CJMCU Beetle USB
|
||||
|
||||
|
||||
|
||||
This is the easiest atmega32u4 to work with thanks to these big USB pads one can solder directly onto
|
||||
|
||||
### PSX to USB or PSX to PS3 adapter
|
||||
|
||||
|
||||
|
||||
While not the smallest and easiest to build with, this is the cheapest and most available adapter from Aliexpress etc..
|
||||
|
||||
Feel free to use a bigger adapter if you're worried about soldering with limited space available.
|
||||
|
||||
### Resistor
|
||||
|
||||
|
||||
|
||||
Not a lot of power to dissipate, so 0.25W will suffice.
|
||||
1K is what's recommended, but 2K, 5K or 10K will work as well.
|
||||
|
||||
Basically take any cheap resistor between 1K and 10K that you can find, it should work
|
||||
|
||||
### Wires
|
||||
|
||||
You need 6 pieces of wire, I recommend using 22 or 24 awg
|
||||
|
||||
### Soldering iron and hot air station
|
||||
|
||||
If available, use hot air and kapton tape to desolder the existing PCB.
|
||||
|
||||
Otherwise you can also use your soldering iron and a desoldering pump or wick.
|
||||
|
||||
### Cutting pliers and wire stripper
|
||||
|
||||
|
||||
|
||||
|
||||
This will be used to prepare wires.
|
||||
|
||||
## Step by step tutorial
|
||||
|
||||
### Step 1: Preparing the adapter
|
||||
|
||||
#### Open the adapter
|
||||
|
||||
Disassemble the adapter by inserting a flat screwdriver above the controller plug and gently twist to separate both halves, exposing the PCB soldered on the connector and USB cable.
|
||||
|
||||
#### Remove USB wires
|
||||
|
||||
Use cutting pliers to remove the 4 usb wires from the PCB.
|
||||
|
||||
#### Remove PCB
|
||||
|
||||
|
||||
|
||||
Protect the plastic with Kapton tape and use hot air to separate the PCB from the controller plug.
|
||||
|
||||
|
||||
|
||||
#### Clean pins
|
||||
|
||||
|
||||
|
||||
Use your soldering iron to clean solder off the pins
|
||||
|
||||
|
||||
|
||||
**Congrats, the controller plug is now ready to be used**, now let's take care of the MCU
|
||||
|
||||
### Step 2: Preparing the MCU
|
||||
|
||||
Note: I suggest flashing the code **BEFORE** soldering anything, but if you forgot to flash it, you can always do it later using the usb cable soldered on it
|
||||
|
||||
#### Resistor and wires
|
||||
|
||||
|
||||
|
||||
Start with the resistor, place it between pins MI and 5V (top and bottom pins from right side of the MCU), but **DO NOT SOLDER YET**, we need to insert wires into these holes as well:
|
||||
|
||||
- Take your 6 wires, strip one end and insert one of each into **MI**, **MO**, **SCK**, **GND**, **5V** and **A2** pin-holes.
|
||||
|
||||
You can now solder everything on MCU side
|
||||
|
||||
|
||||
|
||||
|
||||
#### USB
|
||||
|
||||
Apply tin to the 4 usb pads
|
||||
|
||||
|
||||
|
||||
Then solder the 4 USB wires on them, carefully following the BLACK-GREEN-WHITE-RED order
|
||||
|
||||
|
||||
|
||||
When in doubt, use a multimeter to check which pad is in continuity with GND pin, and which pad is in continuity with 5V pin
|
||||
|
||||
### Step 3: Assembly
|
||||
|
||||
Find a way to place both the cable and MCU inside the adapter, with the controller plug set back into place as well
|
||||
|
||||
|
||||
|
||||
Then it's time to cut wires to a shorter length (you want the minimum length so that you can close the adapter normally)
|
||||
|
||||
|
||||
|
||||
Finally, following the pinout, you can solder everything following the pinout
|
||||
|
||||
```
|
||||
1 2 3 4 5 6 7 8 9
|
||||
-------------------------------
|
||||
| o o o | o o o | o o o | (at the Controller)
|
||||
\_____________________________/
|
||||
|
||||
1 : DAT -> MI (the pin which also has the pullup resistor on it)
|
||||
2 : CMD -> MO
|
||||
4 : GND -> GND
|
||||
5 : 3.3V -> 5V (yes, spec is 3.3v but I've been using 5v without issue)
|
||||
6 : Attention -> A2
|
||||
7 : SCK -> SCK
|
||||
|
||||
```
|
||||
|
||||
**/!\ Pin 1 is on top of the pic** (since this is what the leftmost pin of controller cable will plug into)
|
||||
|
||||
|
||||
|
||||
#### Close the adapter box
|
||||
|
||||
With everything soldered you can now close the adapter by just pressing both sides together it should snap into place
|
||||
|
||||
|
||||
|
||||
I like adding some tape in order not to confuse a modded adapter with a regular one :)
|
||||
|
||||
## Closing words
|
||||
|
||||
Congrats on making your Bemani adapter :)
|
||||
|
||||
Note that you can also flash my LUFAHybridFightstick firmware on it if you take the "PSX" branch and it will serve as a low latency PSX to USB adapter, but I think that's a bit overkill, and doing that without exposing the RST pin will make it hard to flash another firmware on it later on (PROTIP: you can either mod a reset button or solder that RST pin to an unused pin from the PSX plug).
|
||||
|
||||
## Donation
|
||||
|
||||
If this project helps you and you want to give back, you can help me with my future projects.
|
||||
|
||||
While not necessary, donations are much appreciated and will only go towards funding future github projects (arcade hardware ain't cheap :( ).
|
||||
|
||||
Of course you'll also receive my gratitude and I'll remember you if you post a feature request ;)
|
||||
|
||||
[](https://www.paypal.com/donate?hosted_button_id=WT735CX4UMZ9U)
|
||||
|
After Width: | Height: | Size: 26 KiB |
|
After Width: | Height: | Size: 9.8 KiB |
|
After Width: | Height: | Size: 137 KiB |
|
After Width: | Height: | Size: 15 KiB |
|
After Width: | Height: | Size: 435 KiB |
|
After Width: | Height: | Size: 22 KiB |
|
After Width: | Height: | Size: 25 KiB |
|
After Width: | Height: | Size: 22 KiB |
|
After Width: | Height: | Size: 26 KiB |
|
After Width: | Height: | Size: 24 KiB |
|
After Width: | Height: | Size: 25 KiB |
|
After Width: | Height: | Size: 29 KiB |
|
After Width: | Height: | Size: 26 KiB |
|
After Width: | Height: | Size: 30 KiB |
|
After Width: | Height: | Size: 29 KiB |
|
After Width: | Height: | Size: 28 KiB |
|
After Width: | Height: | Size: 33 KiB |
|
After Width: | Height: | Size: 37 KiB |
@@ -14,6 +14,10 @@ This code solves these issues and auto-detects whether a Pop'n Music controller
|
||||
|
||||
You can buy a cheap "Dualshock extension cable" or a dualshock breakout board to build an external adapter box, or you can buy a pre-made adapter from me to support my work :)
|
||||
|
||||
## NEW: DIY GUIDE
|
||||
|
||||
You can now check out the [GUIDE](https://github.com/CrazyRedMachine/BEMANI_PSX_Adapter/tree/main/DIY_GUIDE) for step-by-step instructions on how to build your own adapter!
|
||||
|
||||
## Demo
|
||||
|
||||
https://www.instagram.com/p/CHVLleylqFl/
|
||||
|
||||