diff --git a/README.md b/README.md index 6f3eb3a..ab76c0a 100644 --- a/README.md +++ b/README.md @@ -1,6 +1,8 @@ # chuni-lite Slidy air towers for an arcade chuni slider without backplate. Bare minimum docs because I don't expect too many people to have access to chuni cab sliders without backplates. +![chuni lite](pics/15.jpg) + Current versions can be found at: - CAD: chuni-lite\chunair-cad\airs\print\f1 - PCB: chuni-lite\chunair\chunair\chunair_v2\v2-1-2 & chuni-lite\chunair\chunair_core\v1 @@ -37,16 +39,53 @@ Can hand wire, or replace air_tower_top_1 3D print with chunair pcb. chunair_co Basic steps: 0. Wire up your slider's 12v and DB9. Crimps recommended. 11" 4 wire recommended for 12v, 9" 3 wire for DB9. -1. Print parts. Then print a mirrored set. + +![xa 1](pics/2.jpg) + +![xa 2](pics/3.jpg) + +![xa 3](pics/4.jpg) + +![db9 and 12v](pics/5.jpg) + +1. Print parts. Then print a mirrored set. Glue magnets with super glue except for the one on slider which is inserted from the outside - glue that one in with hot glue. Pay attention to the magnetic poles!! + +![chunair 3d print](pics/1.jpg) + 2. Assemble slider_rail and air_tower with hinge, flat head screws, and nuts and insert into slider (double check orientation) -3. Glue leds/pds if you are using air_tower_top_1. Wire according to the diagram in "ac chuni/wiring.png". If you have PCB, solder resistors and leds/pds. With PCB, recommended wire length is around 30", 9 wires for RGB, 8 for no RGB. + +![hinge](pics/6.jpg) + +3. Glue leds/pds if you are using air_tower_top_1. Wire according to the diagram in "ac chuni/wiring.png". If you have PCB, solder resistors and leds/pds - 10K resistors are marked, the other 3 are 150 ohm resistors. With PCB, recommended wire length is around 30", 9 wires for RGB, 8 for no RGB. 3a. If you want RGB, add a 3 piece WS2812B LED strip in the middle and solder it up like the picture. + +![led](pics/7.jpg) + +![led pcb](pics/8.jpg) + 4. Shove unsoldered end of ribbon cable through the channel. 5. Screw air_tower_top_2 to the pcb or air_tower_top_1(depending on which you have) using rounded m3 heads while threading through air_tower. Don't forget to put the printed bumper piece on one of the screws. + +![bumper](pics/12.jpg) + 6. Solder to Pro Micro or chunair_core pcb depending on what you have. Make sure you slide the slider_rail into the slider first before soldering. + +![chunair core](pics/9.jpg) + 7. Repeat steps 2-6 for the other side. + +![chunair loose](pics/10.jpg) + +![chunair assembled](pics/11.jpg) + 8. Add zip ties to core. Use 4 m3x8 bolts and nuts to mount db9 and chunair_core to core. Press fit 12v barrel connector and hot glue into place. + +![chunair core](pics/13.jpg) + 9. Thread M4 screws through rubber foot and slider to mount to slider. + +![chunair core](pics/14.jpg) + 10. Use existing M4 screws on the chunithm slider to mount core. Zip tie down core & power cable 11. Flash firmware and test to make sure everything works. Then add adhesive rubber feet on each bumper in addition to the bottom of the airs. diff --git a/pics/1.jpg b/pics/1.jpg new file mode 100644 index 0000000..3315303 Binary files /dev/null and b/pics/1.jpg differ diff --git a/pics/10.jpg b/pics/10.jpg new file mode 100644 index 0000000..151001d Binary files /dev/null and b/pics/10.jpg differ diff --git a/pics/11.jpg b/pics/11.jpg new file mode 100644 index 0000000..4a52efe Binary files /dev/null and b/pics/11.jpg differ diff --git a/pics/12.jpg b/pics/12.jpg new file mode 100644 index 0000000..95a6cde Binary files /dev/null and b/pics/12.jpg differ diff --git a/pics/13.jpg b/pics/13.jpg new file mode 100644 index 0000000..dfaa88a Binary files /dev/null and b/pics/13.jpg differ diff --git a/pics/14.jpg b/pics/14.jpg new file mode 100644 index 0000000..9686782 Binary files /dev/null and b/pics/14.jpg differ diff --git a/pics/15.jpg b/pics/15.jpg new file mode 100644 index 0000000..a874286 Binary files /dev/null and b/pics/15.jpg differ diff --git a/pics/2.jpg b/pics/2.jpg new file mode 100644 index 0000000..fb3d5c1 Binary files /dev/null and b/pics/2.jpg differ diff --git a/pics/3.jpg b/pics/3.jpg new file mode 100644 index 0000000..6cbda31 Binary files /dev/null and b/pics/3.jpg differ diff --git a/pics/4.jpg b/pics/4.jpg new file mode 100644 index 0000000..468826b Binary files /dev/null and b/pics/4.jpg differ diff --git a/pics/5.jpg b/pics/5.jpg new file mode 100644 index 0000000..c674838 Binary files /dev/null and b/pics/5.jpg differ diff --git a/pics/6.jpg b/pics/6.jpg new file mode 100644 index 0000000..ca2cf3b Binary files /dev/null and b/pics/6.jpg differ diff --git a/pics/7.jpg b/pics/7.jpg new file mode 100644 index 0000000..bf08529 Binary files /dev/null and b/pics/7.jpg differ diff --git a/pics/8.jpg b/pics/8.jpg new file mode 100644 index 0000000..a4b396b Binary files /dev/null and b/pics/8.jpg differ diff --git a/pics/9.jpg b/pics/9.jpg new file mode 100644 index 0000000..b6551f6 Binary files /dev/null and b/pics/9.jpg differ